The Dynamic Data Sheets are useful for your immediate needs
DINterm64: DIN connector compatible terminal strip break-out to work with PCI2PMC, PCIBPMC, PCIBPMCX2.
PCI-SpaceWire: 4 SpaceWire ports with standard MDM connectors, Half length PCI card, DMA support, Windows® driver
pmc_xm: PMC with user programmable Virtex FPGA, supported with DMA, RAM, mezzanine position, programmable PLL, Windows® driver
pmc_mc_x2: Two position PMC carrier with power supply, arbitration, clock distribution
pmc_mc_x4: Four position PMC carrier with power supply, arbitration, clock distribution
DESWCB: SpaceWire cable to SpaceWire connector board with 28 positions. Used for conversion between system bulk cabling and point-to-point
IP-BiSerial-BA13: New version of IP-BiSerial VHDL with customer requirements. 16 or 32 bit data, programmable parity. Rising edge. 8 and 32 MHz IP clock
PC104p-BiSerial-III-BA14: transmit and receive channel w/ redundant output and selectable input, DMA, UART like protocol w/ marking state, start and stop bits, 16 bits plus cmd/data bit. MSB first. The programmed frequency is 6.25 MHz, Windows® driver
PMC-Wizard: The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems based on Ti TLK2711, Windows® driver
cPCIBPMC3U64ET: Extended Temperature 3U 4HP PMC carrier for cPCI.
PMC-BiSerial-III-OSEH: DMA based, customer specific high speed serial IO. Clock and Data interface. RS-485 IO, DMA, Windows® driver.
PMC-SpaceWire-BS2BI: BiSerial 2 Bit Interface - implementing a serial interface with 2 bits transmitted in parallel. Programmable clock rate with 10 and 50 MHz for 20 and 100 mbit per second transfer rates. LVDS IO, DMA, Windows® driver.
cPCIBPMC6UET: Extended Temperature 6U 4HP Dual PMC carrier for cPCI.
cPCIBPMC3U64ET: Extended Temperature 3U 4HP PMC carrier for cPCI now updated with additional features
IP-CAN: Two Controller Area Network channels. Industry Standard SJA1000 controller with basiCAN and PeliCAN standards
PMC-BiSerial-III-LM5 with a multiport, multichannel design for interchannel non-backplane communication. Up to 8 boards can be interconnected with the bezel or rear IO. Programmable speed, direction, DMA support.
PCI-Altera-485 customized VHDL support for Northrop Grumman.
PCI-Altera-PLUS Enhanced version with 20K600, 8K deep FIFOs between Xilinx and Altera, larger Xilinx with expanded internal FIFO
IP-CARA Custom Serial Interface using ARINC 429 electrical standard. 24 bit serial, trianary logic, FIFO [1K x16 per channel] programmable speed, interrupts.
cPCI2PMC Customized to bring RQST/GNT/Clock lines out to operate in the bus master slot. Rework to standard cPCI2PMC design. Fab to be upgraded later
DESWBO Dynamic Engineering SpaceWire Break Out. In line connections with buffering to allow SpaceWIre snooping for errors and activity. Test points and LEDs. Plug and Play operation.
IndustryPack 1553 Interface 1553 Single and Dual Redundant BC, RT and Monitor capabilities. Shunt select Direct or Transformer coupled.
PC104p2PMC PMC adapter for PCI-104 or PC/104p. Add a PMC card to your PC104p stack
MDS1 version of PMC BiSerial III PMC-BiSerial-III-MDS1 custom IO for airborne application. Read data from multiple temperature sensors using a manchester encoded interface. Linux driver and VHDL developed.
PMC SpaceWire Upgrade The VHDL and Driver for the PMC and PCI SpaceWire designs has been updated to include a 4 channel DMA capability and time code. The DMA update provides independent operation of the channels and the ability to run much larger data blocks without CPU intervention. The update is shipping now. Owners of revision 2 and later hardware can update their cards by returning to Dynamic Engineering with a PO to cover the nominal programming and test time. Updated manuals for the hardware and driver are available on the PCI and PMC webpages.
PCI / PCI-X PMC Interface 1/2 length PCI and PCI-X compliant PMC carrier. Differential impedance controlled matched length routing from Pn4 to SCSI connector
PMC-BiSerial-III-LM6: DMA based, customer specific high speed serial IO. Clock and Data interface. LVDS IO, DMA, Windows® driver.
PC104p Chassis Mechanical enclosure for PC104, PC104p, and PCI-104 applications. Cards are stacked and assembled into internal frame. Internal frame is isolated from external chassis with bumper pads. Built in gaskets, heatsink, mounting flange. Multiple lengths available. Custom cutouts and labeling available. Black anodized extruded aluminum chassis and aluminum endcaps. Chassis comes complete with external housing and internal frame, bumper pads, end caps and gaskets.
PMC-BiSerial-III-TRANS-HW4 - updated version of PMC BiSerial III with transformer coupled IO and conduction cooling. HW4 is the first customized version, and features manchester encoding/decoding full and half duplex operation, Dual Port RAM. 8 independent channels.
PMC-BiSerial-III-HW2 - SDLC and asynchronous protocols added to upper channels of HW1 design. Full and half duplex support for SDLC.
cPCI4IP-MM - updated version with a minimized PCI memory requirement. One eighth of the standary memory requirement. Full IO, INT and ID spaces. 64K the MEM space for each of the 4 slots.
PCI-SpaceWire and PMC-SpaceWire - New option available with deep FIFOs - 128K x 32 on TX and on RX for channel 0. -128 option.
IP-CAN Windows® driver now available. Extensive testing done with multiple node long and short networks, termination options, ISO and Direct connect. IP Driver compatible with all Dynamic Engineering Carrier drivers for maximum portability. Updated fab with software programmable bus termination supported by the driver. User reference software included when driver is ordered. We are considering doing a GUI for this one with some expanded - application level features - address snoop and so forth. Manuals available at the bottom of the dynamic data sheet.
Updated, redesigned Linux base driver for PCI3IP, PCI5IP carriers is done. Now porting to cPCI2IP, cPCI4IP, PC104pIP, PC104p4IP. First IP level driver is for the IP-QuadUART. Generic driver included with carrier driver allows any IP to be used with the carrier.
New design PCIeBPMCX1 PCIe [PCI Express]1/2 length format carrier / adapter for PMC. PCI32/33 up to PCI-X speeds with 4 lane PCI Express interface. Local Power supplies to operate without a power cable. "Zero Slot Fan"™ options. By customer request we cut down the connector and made a single lane version of the card. Fully tested and compliant. The PCIeBPMC is a copy of the PCIeBPMCX1 with reduced lane count for situations where the PMC is 32/33 or intermittent operation at a higher frequency is required. Compatible with 1 lane PCIe slots. For full PCI-X operation use the PCIeBPMCX1.
IP-QuadUART : Driver developed for Linux environment. Linux parent driver has been designed and ported to PCI3IP, PCI5IP, cPCI2IP, cPCI4IP, PC104pIP, and PC104p4IP carriers. The first child driver to go with the carrier drivers is for IP-QuadUART, and is now completed. The carrier driver comes with a generic driver module to act as the child driver for IP´s without a Linux driver written. The generic driver allows third party designs without native linux drivers to be used with the Dynamic Engineering Carrier Drivers for Linux as well as any Dynamic Engineering cards not yet supported. Example software using the generic driver is included.
PMC BiSerial BAE1 : Driver developed for Windows® environment. Initial design had VxWorks support. New client with different requirements.
PC104p-BiSerial-III-DDL : Port of IP-OctalSerial-FCS to PC104p-Biserial-III platform plus driver. Delivered. T&I at customer complete
PCI-Harpoon : New design with PCI format, 4 interface channels each with serial differential, power sense for 28V circuits, power sense for 115V AC single and 3 phase, switched 28V output power. Dynamic Data Sheet T&I completed at customer site.
PCI-Altera-FM1: Serial interface designed for customer support on the PCI-Altera. VHDL and Driver for customer maintained design. Delivered.
on each channel.
VME-6U-COOL 6U VME format design with up to 12 Fan positions. Low Profile "Zero Slot Fans"™ with options for Forward and Reverse Air Flow. +12 or +5 option for fan power
cPCI-6U-COOL 6U cPCI format design with up to 12 Fan positions. Low Profile "Zero Slot Fans"™ with options for Forward and Reverse Air Flow. +12 or +5 option for fan power
PMC Parallel TTL BA16 customized version of PMC Parallel TTL design. DMA based FIFO supported programmable output with byte wide DMA supported input function. Linux Driver. Tested in PMC MC X4 with PrPMC.
Windows® Win32 model [XP/2000 etc.] driver for PMC Serial RTN5 Completed
HDEterm68: DIN connector compatible terminal strip break-out to work with PCI2PMC, PCIBPMC, PCIBPMCX2, PCIeBPMCX1 etc.. Recently updated [10/08] to have differentially routed, matched length, controlled impedance traces between connectors and screw terminals.
PCIBPMCX2: Updated design to allow for "Zero Slot Fans"™ capabilities, improved power supply, and matched length IO. 11/08. Now shipping
PMC BiSerial ORB2 customized version of PMC Biserial III design. ORB2 has 2 channels each of 4 different protocols. Mixed 485 and LVDS IO, Ternary, Low Speed, High Speed, and Telemetry interfaces. External FIFO's implemented on High Speed channels to provide 132K x 32 of storage per channel. Each channel is half duplex. Programmable data rates, inversion of control signals, other programmable options on each channel. Windows® driver. 2/09
PMC Parallel TTL BA17 customized version of PMC Parallel TTL design. Change of State detection with Time Tag, Data storage supported with DMA. Window® driver developed at Dynamic Engineering, VxWorks driver developed by client. BA17 has been ported to the BA18.
ccPMC Parallel TTL BA18 customized version of ccPMC Parallel TTL design. BA18 started with the BA17 features ported to a conduction cooled version of the PMC Parallel TTL card. In addition 8 ADC's [12 bit, 10 MHz max] were added each with FIFO support, DMA, and compression. Windows® driver. 2/09
PMC BiSerial BA19 customized version of PMC Biserial III design. BA19 uses a byte wide port to transfer data between a Master and a Target device. Programmable data rate, handshake, FIFO's with DMA for each port. Windows® driver. 2/09
PC104p SpaceWire New design based on PCI SpaceWire PC104p and PCI-104 compatible. Now Shipping. See HW and SW manuals on PCI SpaceWire page. Linux and Windows® drivers available. Available Now.
PCI-ASCB New design based PCIBPMCX2, PMC-BiSerial-Trans. Differential Ethernet processing on a PCI board with an available PMC slot for local processing. Dual Port RAM is used in ASCB; DMA function has been updated to work with address based memory. Design complete and tested. First run of 30 PCI-ASCB boards complete.
ccPMC-SpaceWire Conduction cooled version of the PMC SpaceWire design with special option for Rad Hard FLASH. 4 channels supported with DMA, TimeCode, frequency selection, internal and optional external memory.
Design updated PC104p Chassis redesigned thermal springs at end plate for greater surface area in contact. Redesigned inner frame end cap for more user connector space.
ccPMC-Parallel-TTL ccPMC [conduction cooled] format upgrade to industry standard PMC Parallel IO. 64 independent TTL IO or 32 TTL and 8 ADC. External or Internal clocking options. Programmamble PLL. Change of State [COS] interrupts on each channel [rising, falling, both, neither]. FIFO or register based. Direct access or DMA. Rear Panel IO. ROHS or Standard processing.
PMC-Parallel-TTL Upgrade to industry standard PMC Parallel IO. 64 independent TTL IO. External or Internal clocking options. Programmamble PLL. Change of State [COS] interrupts on each channel [rising, falling, both, neither]. FIFO or register based. Direct access or DMA. Front Panel, Rear Panel or both IO options. ROHS or Standard processing.
IP-Reflective Memory is a self configuring networked memory card. Write to the local memory [256K x 16] and automatically update the other copies on the network. Local copies mean local access speed. Rj45 connector system or IP Module IO connector. Windows® driver available. Custom rates, LVDS IO, up to 256 nodes in a system.
ccPMC-HOTLink New design with 6 HOTLink channels plus 12 differential IO. Conduction Cooled PMC, LInux and Windows® drivers, reference software, manuals.
