| Size |
single slot Type 2 IP Module [max height on rear = .055" / 1.4 mm].
|
| |
|
| IO |
24 independent RS485/RS422 transceivers. 40 MHz max. Programmable termination. Unused bits can be used as a parallel port.
|
| |
|
| Speed |
8 and 32 MHz IP bus operation. Up to 40 MHz on IO.
|
| |
|
| IP decoding |
ID, IO, Mem and INT spaces supported
|
| |
|
| Memory |
8 FIFOs are supplied - one per channel. The FIFOs are designed to support independent operation on each channel.
|
| |
|
| Clocks |
Internally generated and externally supplied clocks are supported with source selection and programmable divider.
|
| |
|
| Access Width |
all addresses are on 16 bit boundaries
|
| |
|
| ID PROM |
Each version of the IP-OctalSerial has a unique ID PROM for identification.
|
| |
|
| Write cycle to TX FIFO |
Write cycles to the FIFO are supported with a write through buffer. Also multiple FIFOs can be loaded with a single write operation when the same data set is to be sent from multiple ports.
|
| |
|
| Write cycle to RX FIFO |
Write cycles to the RX FIFO are supported for loop-back testing.
|
| |
|
| Software Interface |
All registers are read-write. All registers on word addresses. Each channel has the same relative bit definitions. Each channel as separate control registers.
|
|
|
| Interrupts |
Programmable interrupts for each channel are supported. Masked interrupts can be used in polled mode by reading the status register. Interrupts are mapped to INTR0n on IP bus.
|
| |
|
| Power Requirement |
+5V |
| |
|
| Oscillator |
Provision for a local oscillator to generate custom frequencies. |
| |
|
| MTBF |
1.49 million hours Bellcore SR332 MTBF |
| Speed |
The transmit memory can be loaded quickly. 32 bit accesses are supported by loading from the memory space. Multiple FIFOs can be loaded in parallel. Data write through is supported. Reading from the RX FIFO has also been optimised to support high speed operation. 32 and 8 MHz IP clock rates are supported. The Xilinx can handle high speed serial or parallel protocols. The IO are rated at 40 Mhz.
|
| |
|
| Price |
The IP-OctalSerial has the low price point. Up to 8 channels in one slot means fewer slots used. Fewer slots and higher performance are a winning combination.
|
| |
|
| Ease of Use |
The OCTALSERIAL is easy to use. Please download the manual and see for yourself. The engineering kit provides a good starting point for a new user. The reference software does a loop-back test and set-ups the different modes of operation.
|
| |
|
| Availability |
The IP-OctalSerial is a popular board. We keep the IP-OctalSerial in stock. Send in your order and in most cases have your hardware the next day - delivered to you via FedEx.
|
| |
|
| Size |
The IP-OctalSerial in standard configuration is a Type 2 size IP module which conforms to the IndustryPack mechanical and electrical specifications. Only .055" on the rear means no mechanical interference issues. The IP-OctalSerial can be used in all IP slots.
|
| |
|
| IP Compatibility |
The IP-OctalSerial is IP compliant per the VITA 4 - 1995 specification. All Dynamic Engineering IP Modules are compatible with PCIe3IP, PCI3IP, PCIe5IP, PCI5IP , cPCI2IP, cPCI4IP, PC104pIP, and PC104p4IP. The IP-OctalSerial will operate with any IP specification compliant carrier board. |
