Made in USA
The Embedded Solutions Experts
IP-Relay16
IP Module with 16 Form C Relays, High or Low side switch 220VDC, 250 VAC, 1.5A
IP-OptoISO-16 Description
- Driver included with purchase
- Standard Type II module
- 8↔32 MHz. operation
- 220VDC, 250VAC, 60W 62.5VA, UL, RoHS, IEC 61810 RT V, IEC 60529 IP 67 rated relays.
- 16 ´Outputs´ ↣ NO, NC, COM for each Relay. 1.5A traces on each signal to IP IO connector.
- Any combination of High Side or Low Side switches
- make most Forms with combinations of switches. See HW manual
- Fused 3.3V output reference
- 1 year warranty standard. Extended warranty available.
- Extended [Industrial] Temperature standard.
- ROHS and Standard processing available
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light, easy to mix and match for your application.
.
IP-Relay16 is an IndustryPack Module with 16 relays. Each relay implements a form C SPDT switch. The relays are hermetically sealed, high shock and vibration resistant, plus fast. Typical switching times of 1 mS.
The design utilizes a Xilinx CPLD to provide the IP interface - IDPROM, Bus interface, registers, and control for the relays. Each relay has a separate bit in the control register to allow for independent operation.
IP-Relay16 can be used to replace the Systran Relay16 design also known as "B-T-MR-RELAY16#-A-0-A2" . The IO definitions are common and minimal SW changes would be required to use IP-Relay16.
The relays are controlled by the host by setting or clearing bits in the Relay Control register. Each bit corresponds to one relay. When set the relay is energized. When cleared the relay is returned to the default state. Back EMF protection is provided on the control side of the relay. The voltage rating on each relay is up to 220 VDC, 250 VAC and 60W or 62.5 VA. The IP IO connector is limited to about 1 A per pin. The traces on the IP are rated for 1.5A. Please check with your IP carrier for maximum current capabilities. Please contact Dynamic Engineering if you need a carrier with power traces.
Each of the Relays provides a SPDT or Form C type switch. By using only the NO [normally open] side or only the NC side [normally closed] and COM [common] you can make Form A and B switches. In addition with cascaded switches most of the other defined switch forms can be created. The hardware manual has details including the cross connections and order to energize or de-energize the relays for proper operation.
Design note: It is the clients responsibility to provide proper EMF protection on the system side of the relays. With improper protection the life span of the relays may be reduced. This is not a warranty item.
There is ample room within the CPLD to add custom state-machines etc. as your needs require.
Please contact Dynamic Engineering with any special requirements.
The IP Module driver can be instantiated multiple times to control multiple cards by the same CPU. IP-Relay16 when coupled with the Dynamic Driver "knows" what slot it is in and which carrier it is installed into. The slot and carrier information is required when using multiple cards in a PCI/PCIe system with dynamic address assignment. A known system configuration can be combined with the slot and carrier information to deterministically access the right card
PCI implementations can be done with PCI3IP and PCI5IP. Applications from 1 to 80 Relays per PCI slot.
PCIe is supported with the PCIe3IP and PCIe5IP. Applications from 1 to 80 Relays per PCIe slot.
cPCI 3U is supported with cPCI2IP. Applications with 1 to 32 Relays per 3U cPCI slot.
cPCI 6U is supported with cPCI4IP. Applications from 1 to 64 Relays per 6U cPCI slot.
PC104p is supported with PC104pIP. Applications with 1 Relays per PC104 stack position.
PC104p situations with a custom mechanical can be done with the PC104p4IP.
Applications from 1 to 64 Relays per per PC104 stack position.
3U VPX is supported with VPX2IP. Applications with 1 to 32 Relays per 3U VPX slot.
6U VPX is supported with VPX4IP. Applications from 1 to 64 Relays per 6U VPX slot.
.
IP-Relay16 is an IndustryPack Module with 16 relays. Each relay implements a form C SPDT switch. The relays are hermetically sealed, high shock and vibration resistant, plus fast. Typical switching times of 1 mS.
The design utilizes a Xilinx CPLD to provide the IP interface - IDPROM, Bus interface, registers, and control for the relays. Each relay has a separate bit in the control register to allow for independent operation.
IP-Relay16 can be used to replace the Systran Relay16 design also known as "B-T-MR-RELAY16#-A-0-A2" . The IO definitions are common and minimal SW changes would be required to use IP-Relay16.
The relays are controlled by the host by setting or clearing bits in the Relay Control register. Each bit corresponds to one relay. When set the relay is energized. When cleared the relay is returned to the default state. Back EMF protection is provided on the control side of the relay. The voltage rating on each relay is up to 220 VDC, 250 VAC and 60W or 62.5 VA. The IP IO connector is limited to about 1 A per pin. The traces on the IP are rated for 1.5A. Please check with your IP carrier for maximum current capabilities. Please contact Dynamic Engineering if you need a carrier with power traces.
Each of the Relays provides a SPDT or Form C type switch. By using only the NO [normally open] side or only the NC side [normally closed] and COM [common] you can make Form A and B switches. In addition with cascaded switches most of the other defined switch forms can be created. The hardware manual has details including the cross connections and order to energize or de-energize the relays for proper operation.
Design note: It is the clients responsibility to provide proper EMF protection on the system side of the relays. With improper protection the life span of the relays may be reduced. This is not a warranty item.
There is ample room within the CPLD to add custom state-machines etc. as your needs require.
Please contact Dynamic Engineering with any special requirements.
The IP Module driver can be instantiated multiple times to control multiple cards by the same CPU. IP-Relay16 when coupled with the Dynamic Driver "knows" what slot it is in and which carrier it is installed into. The slot and carrier information is required when using multiple cards in a PCI/PCIe system with dynamic address assignment. A known system configuration can be combined with the slot and carrier information to deterministically access the right card
PCI implementations can be done with PCI3IP and PCI5IP. Applications from 1 to 80 Relays per PCI slot.
PCIe is supported with the PCIe3IP and PCIe5IP. Applications from 1 to 80 Relays per PCIe slot.
cPCI 3U is supported with cPCI2IP. Applications with 1 to 32 Relays per 3U cPCI slot.
cPCI 6U is supported with cPCI4IP. Applications from 1 to 64 Relays per 6U cPCI slot.
PC104p is supported with PC104pIP. Applications with 1 Relays per PC104 stack position.
PC104p situations with a custom mechanical can be done with the PC104p4IP.
Applications from 1 to 64 Relays per per PC104 stack position.
3U VPX is supported with VPX2IP. Applications with 1 to 32 Relays per 3U VPX slot.
6U VPX is supported with VPX4IP. Applications from 1 to 64 Relays per 6U VPX slot.
IP-Relay16 Features
Size
1.8 x 3.9 inches nominal Type II with low profile components on rear
IO
16 independent SPDT relays. Make most forms with single or combined relays.
Clocks
Compatible with 8 and 32 MHz IP bus operation.
IP Decoding
ID, IO, INT, MEM spaces supported. IO space for Relay control, Revision. ID for IDPROM. Mem and INT not currently utilized.
Software Interface
Control registers are read-writeable
Windows®, reference SW and Drivers
Windows®, reference SW and Drivers
Power Requirement
+5V. Typical 250 mA @ 5V with 8 relays energized. 4.75 ↔ 5.25V, no +/- 12V used
Interface
220 VDC, 250 VAC, 60W, 62.5 VA, 1.5A rated traces [10 degree rise], NO, NC, COM per relay. 1 mS typical switch on/off.
Isolation
The relays provide 1500 Vrms surge between open contacts.
Initialization
Relays are de-energized after reset.
Ratings
Relays have UL, RoHS, IEC 61810 RT V, IEC 60529 IP 67. 10(8) operations per relay. Low power operations ~ 2M.
Reliability
TBD million hours. Bellcore. GB 25c
IP-Relay16 Benefits
Speed
IP-Relay16 can operate with 8 and 32 MHz IP reference clocks for fast IP bus interaction. The on time, and off time are approximately 1 mS which is rapid for this type of IO. Since this is a mechical relay if your application requires rapid, sustained switching IP-OptoISO may be better suited.
Price
System level cost is best when reasonably priced reliable hardware is used and NRE minimized. With IP-Relay16, driver support for the carrier and IP level, reference software, history of reliable operation, and fantastic client support your cost per unit and overall costs are attractive.
Ease of Use
IP-Relay16 is designed to be easy to use. Direct access to all features, aligned registers for larger access types, programmable features to allow personalization for your system. Please download the manuals and see for yourself. Reference software is provided in source form to get you started.
Availability
IP-Relay16 is classified as a stocked item.
IP Specification Compatibility
IP-Relay16 is compliant per the VITA 4 - 1995 specification. Tested with PCI and PCIe based carriers. All Dynamic Engineering IP Modules are compatible with the PCIe3IP, PCIe5IP, VPXI2IP, PCI3IP, PCI5IP, cPCI2IP, cPCI4IP, PC104pIP etc. IP-Relay16 will operate with any IP specification compliant carrier board.
Part Number: IP-Relay16
Ordering Options
- IP-Relay16 Standard board - 16 SPDT Form C Relays , Industrial temperature components.
- -ROHS Use ROHS processing. Standard processing is ""leaded"
- -CC Option to add Conformal Coating
- -XXX See Manuals section for customized versions and replace XXX with type
IP-Relay16 Drivers
Software Support for IP-Relay16 includes: Windows® and Linux compliant drivers
The IP driver is layered and operates on top of the Carrier driver. IP drivers are auto installed for each instance detected. Please see the Driver manuals for the specifics of each type.
Drivers and Reference SW are developed for each type / version of IP-Relay16 implemented. When custom versions are ordered the NRE will include providing Windows, Linux, and/or VxWorks packages. For off-the-shelf models, select on the manuals tab, the Windows® and Linux SW shown is included with your purchase of the HW. A small one-time charge is required for the VxWorks versions. Unsupported SW versions may have an NRE requirement.
Integration support is available. Please contact Dynamic Engineering for this option or download the Technical Support Description from the Company button.
Reference diagam of how our Linux Driver / Application layer operate with the Carrier and IP Module.
The IP driver is layered and operates on top of the Carrier driver. IP drivers are auto installed for each instance detected. Please see the Driver manuals for the specifics of each type.
Drivers and Reference SW are developed for each type / version of IP-Relay16 implemented. When custom versions are ordered the NRE will include providing Windows, Linux, and/or VxWorks packages. For off-the-shelf models, select on the manuals tab, the Windows® and Linux SW shown is included with your purchase of the HW. A small one-time charge is required for the VxWorks versions. Unsupported SW versions may have an NRE requirement.
Integration support is available. Please contact Dynamic Engineering for this option or download the Technical Support Description from the Company button.
Reference diagam of how our Linux Driver / Application layer operate with the Carrier and IP Module.
IP-Relay16 Manuals
Click on the links to Download selected manuals in PDF format.
IP Carrier and Module Quick Start guide for Windows®7
IP Carrier and Module Quick Start guide for Windows®10
IP-Relay16 Rev 01p1 Hardware Manual in PDF format.
IP-Relay16 Rev 01p0 Win10 Manual in PDF format.
IP Carrier Linux Manual
Linux IP Module Manual
VxWorks IP Module Manual
Download the IP-Relay16 Statement of Volatility
IP Carrier and Module Quick Start guide for Windows®7
IP Carrier and Module Quick Start guide for Windows®10
IP-Relay16 Rev 01p1 Hardware Manual in PDF format.
IP-Relay16 Rev 01p0 Win10 Manual in PDF format.
IP Carrier Linux Manual
Linux IP Module Manual
VxWorks IP Module Manual
Download the IP-Relay16 Statement of Volatility